Professional Documents
Culture Documents
Excellent Strength and Durability • Exceptional Chemical Resistance • Seamless System • Fully Bonded to Slab • Redundant Protection
System Description
System III MB is a field installed composite
waterproofing and gas vapor barrier that is comprised
of a water-based polymer modified asphalt (PMA)
membrane sandwiched between two HDPE and
polypropylene fabric laminate sheets which provides
the durability and chemical resistance of HDPE with the
constructability and installation efficiencies of a PMA.
(See below for special designs for water table
conditions.)
System Components
ON
R
TI
W a te r p r oo f i n g Sys tems EA I
R
LW ND
ORLD CO
800-882-1896 • www.eproserv.com
rev. sys3-mb_042111
epro • System III MB - Moisture / Gas Barrier
Epro Below Slab Water / Gas Barrier Composite System Testing
Composition HDPE film and polypropylene fabric laminate and polymer modified asphalt and HDPE film and
polypropylene fabric laminate. ( Ecoshield-P / Ecoline-S / Ecoshield-PP )
Tensile Strength* ......................... ASTM D-412 ..... 662 psi Chemical Permeation** .... ASTM F-739 Perm Rate Perm Rate
Elongation* .................................. ASTM D-412 ..... 45% Ug/cm2 ml/day
Adhesion to Concrete*** .............. ASTM C-836 .... 27 lbf/in Chlorinated Solvent
Puncture Resistance .................... ASTM D-1709 ... 310.9 lbs Perchloroethylene ................................... 69.4 .......... 0.0008
Hydrostatic Pressure ................... ASTM D-5385 ... 369.5 ft. Trichloroethylene ........ ............................ 89.8 .......... 0.0012
Aromatic Hydrocarbon
Soil Burial* ................................... ASTM D-4068 Benzene .................... ............................ 59.3 .......... 0.0013
Weight change ..................... See Note 1 ........ 1.2% ......... passed
Tensile Strength ................... See Note 1 ........ 9.89% ....... passed Chemical Resistance** ...... ASTM D-543 Net change
Elongation ............................ See Note 1 ........ 2.2% ......... passed Chlorinated Solvents .. ASTM D-882 Mod. (Less 10% pass)
Perchloroethylene
Heat Aging* ................................. ASTM D-4068 Weight ........................ ............................. 4.1%
Tensile Strength .................. See Note 1 ....... 8.6% ......... passed Tensile Strength ......... ............................. 6.5%
Elongation .......................... See Note 1 ....... 8.9% ......... passed Tricholorethylene
Weight ........................ ............................. 5.4%
Environmental Stress Cracking* .. ASTM D-1693 Tensile Strength ......... ............................. 6.0%
Failure ................................ See Note 2 ........ 620 hrs. .... passed
Aromatic Hydrocarbon
Oil Resistance* .......................... ASTM D-543 & Benzene
ASTM D-412 Weight ........................ ............................. 4.1%
Weight change ............................ See Note 1 ....... 7.6% ......... passed Tensile Strength ......... ............................. 4.4%
Tensile Strength ................. See Note 1 ....... 1.1% ......... passed
Elongation .......................... See Note 1 ....... 4.4% ......... passed Gases
Hydrogen Sulfide
Methane Transmission* .............. ASTM D-1434 Weight ........................ ............................. 0.6%
See Note 3 ....... 3.70xE-15.. passed Tensile Strength ......... ............................. 0.8%
ON
R
Wa te r p r oo f i n g Sys tems
TI
EA I
R
LW ND
O RL D C O
Note 1: LA requires less than 10%
Note 2: LA requires over 500 hrs. 800-882-1896 • www.eproserv.com
Note 3: LA requires less than 3 ml per day
rev.sys3mb_042111