You are on page 1of 18

LGE Internal Use Only

LGE Internal Use Only

ChipErase Download Guide



1. Pre-condition
2. Backup
3. Flash Image(Binary)
4. Restore
5. Factory Reset

2014. 4.
MC R&D / LGE

Configuration

LGE Internal Use Only

QPST
1. Unzip QPST_2.7.411.zip file
2. Install QPST (QPST.2.7.411.msi)
(If QPST is already installed, you dont have to be)

TestMode Tool
1. Unzip TestMode_9.7_Tool.zip file
2. Run vsflex7l_ocx_regist.bat
(If TestMode Tool is already installed, you dont have to be)

IMEI, BT, WiFi MAC Backup (1/3)


1.
2.
3.
4.
5.

LGE Internal Use Only

Connect Device to PC (with USB cable) -> Select USB Connection : LG software
Run TestMode9.2.exe
Check if the Auto Comport is enabled
Click the Connect button
Verify Port Open Successed!

IMEI, BT, WiFi MAC Backup (2/3)

LGE Internal Use Only

6. Select BT_WIFI_IMEI.CFG file

IMEI, BT, WiFi MAC Backup (3/3)

LGE Internal Use Only

7. Double Click IMEI read, Bluetooth read, WIFI MAC ADDRESS READ
8. Copy IMEI, BT, WIFI MAC Address value
(Click the responsed value -> Ctrl+C -> Open Notepad -> Ctrl+V )
9. Close TestMode Tool

QCN backup Add New Port (1/5)

LGE Internal Use Only

**Caution: Launch QPST Configuration after Closing TestMode Tool


1. Execute QPST Configuration Program:
(Start -> Programs -> QPST -> QPST Configuration )
2. Click the Add New Port button

QCN backup (2/5)

LGE Internal Use Only

3. Uncheck(disable) Show Serial and USB/QC Diagnostic ports only


4. Select LGE AndoridNet USB Serial Port -> OK

QCN backup (3/5)

LGE Internal Use Only

5. Click Start Clients-> Software Download

QCN backup (4/5)

LGE Internal Use Only

6. Click Backup tab and check if Port is enabled


(COMxx MSM8974 .)
7. QCN File: Click the Browse button
8. Select directory and make a name of QCN file to
be going to backup
9. Click Save(S) button

QCN backup (5/5)

LGE Internal Use Only

10. Click the Start button. Then wait for until Total
Progress bar will be 100%.
11. Click Exit button

10

Flash Image (CHIPERASE)

LGE Internal Use Only

1. Execute LGUP -> Select CHIPERASE -> Select tot File -> Start
2. Check if the device bootup with Mini OS after flashing binary.
3. Reset Device with Normal mode : Push the Power Button + tab Normal Boot(+power) in Mini OS screen

11

IMEI, BT, WiFi MAC restore (1/3)


1.
2.
3.
4.
5.

LGE Internal Use Only

Connect Device to PC (with USB cable) -> Select USB Connection : LG software
Run TestMode
Check if the Auto Comport is enabled
Click the Connect button
Verify Port Open Successed!

12

IMEI, BT, WIFI MAC, NTCode Write (2/3)

LGE Internal Use Only

6. Select BT_WiFi_IMEI_NTCODE.cfg
7. Double Click IMEI write -> input backuped IMEI value ->OK -> Check if the Response: OK!

13

IMEI, BT, WIFI MAC, NTCode Write (3/3)

LGE Internal Use Only

Write NT Code, Bluetooth Address, WIFI MAC Address


8. NTCODE Write : "1","FFF,FFF,FFFFFFFF,FFFFFFFF,11"
9. Bluetooth write : backup value
10. WIFI MAC ADDRESS WRITE : backup value

14

QCN Restore (1/3)

LGE Internal Use Only

**Cautions: Close TestMode tool before executing QPST Configuration


1.
2.
3.
4.

Execute QPST Configuration program


Check if the port is enabled
If the port is not enabled, Add New Port (refer to the page 6 ~7)
Click Start Clients -> Software Download

15

QCN Restore (2/3)

LGE Internal Use Only

5.
6.
7.
8.

Select Restore tab


Check if the Port is enabled(COMxx MSM8974 .)
Click the Browse button
Select qcn file that you ackup -> Click Open(O) button

16

QCN Restore (3/3)

LGE Internal Use Only

9. Click Start. Then Wait for until status will be Memory Restore
Completed (The device will reset during restore qcn file)
10. Exit

17

Factory Reset

LGE Internal Use Only

Factory reset should be performed in Hidden Menu as follows.


1. Dialer > 3845#*722#
2. Hidden Menu > WCDMA Only > Factory Reset
3. After Factory reset is completed, start to test

18

You might also like