You are on page 1of 7

SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

Product Catalogue
• Girth SAW Welder
is a self-propelled submerged arc welding system applicable for
bottom-up and Top-down constructed wall storage tanks. This type
Of machine can serve both construction methods.

Specification:
width of plate :1.4-3.2 m adjustable seam :horizional and girth seam
diameter of tank :> 4 m current :300-550A
welding speed :10-3000mm/min Votage :20-40V
thickness of plate: 8-80mm power set : 380v/50Hz
Type of steel :all steel stucture shape of groove: V or K

Applicable for
•Bottom-up
•Top-down
•Single wall
•Double wall
•Inside
•Out side

Working on bottom-up construction state working on Top-down construction state

Email: paulzhangxiang@hotmail.com T:(86)13804970967


SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE
Product Catalogue
•Vertical Electrogas welder
Vertical Electrogas welder is high efficient welding machines to weld the vertical jointof
tank shell for the thickness range from 8MM up to100MM( AND MORE), only one
pass welding needed for the vertical jiont, the effeiceny is 30 times to manual welding.
For the plate of 3.2M width and average thickness 25MM, the average welding time is 30
minutes. Our machines welding process is Electrogas ,better than FCAW which need
multi-pass welding.
Specification;
thickness:8-100mm type of steel :all type of steel shape of groove :V, X
position :Vertical joint width of plate :1.0-3.2m current :300-500 A
votage :20-40V power set : 380v diameter of wires : 1.6mm flux cored
cooling : water cooling 8m3/h weld head adjustment : 5 waver : 4 parameter
welding speed :feedback control full speed :3000mm/min gas :CO2 30L/min

One pass solve


•Inside
•Outside

Model GHL-II for bottom up construction Model DLH-II for Top -down construction

Email: paulzhangxiang@hotmail.com T:(86)13804970967


SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

Product Catalogue
•Fillet&Butt SAW Welder
Fillet&Butt SAW Welde mainly applied in the auto welding of
inner fillet & outer fillet, butt seam and lap on the bottom plate of
large oil storage tank erection project.
Specification
Rated welding current: 600A\ 1000A
Minimum diameter of Inner fillet : >5M
Minimum diameter of outer fillet :>5M
Speed: 0—2000mm/min
Diameter of wire: standard: 3.2
Optional: 2.4、、4.0、4.8/5.0
Wire reel specification/weight inner D. 300mm/25kg
Control cable:15m/piece ( standard )
Welding cable: 15m/piece + ground wire 3m/piece , 120 mm2/piece
Weight of tractor: 45kg
Size of tractor: 980mm×535mm×830mm

Butt welding

Fillet welding

Email: paulzhangxiang@hotmail.com T:(86)13804970967


SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

Tank fabrication method


Bottom –up
The machines hang on the wall of tank ,riding on the edge of shell, bottom
layer is fabricated first ,and then crane the machines to ride on the seond layer
To weld the seam between the two layers, one layer after another

Email: paulzhangxiang@hotmail.com T:(86)13804970967


SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

Lift up the upper layer Top –Down


fabricate the top layer, and then use jacks
lift up this layer make a gap for the beneath
Layer ,put the next layer fill out the gap and
use Machines to weld the seam,the machines
are Ranning on the rails mounted in the
ground
Tank fabrication method

Weld the seam

Jack system

Email: paulzhangxiang@hotmail.com T:(86)13804970967


SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

Project DEMO

Australia working site Sudan working site

Uruguay working site Peru working site india working site


Email: paulzhangxiang@hotmail.com T:(86)13804970967
SHENAYNG UNIVERSITY AUTO WELD RESEARCH INSTITUTE

• THE END
• More information and VEDIO
• pls go to
• www.tankwelder.com

Email: paulzhangxiang@hotmail.com T:(86)13804970967

You might also like