You are on page 1of 29

MAE 3130: Fluid Mechanics

Lecture 10: Internal and External Flows


Spring 2003
Dr. Jason Roney
Mechanical and Aerospace Engineering
Outline
• Overview of Viscous Pipe Flow
• Laminar Pipe Flow
• Turbulent Pipe Flow
• Dimensional Analysis of Pipe Flow
• Overview of External Flows
• Boundary Layer Characteristics
• Pressure Gradients Effects
• Lift and Drag
• Some Example Problems
Viscous Pipe Flow: Overview
Pipe Flow is important in daily operations and is described in general as
flow in a closed conduit (pipes and ducts). It is also known as an internal
flow.
Some common examples are oil and water pipelines, flow in blood vessels,
and HVAC ducts.
When real world effects such as viscous effects are considered, it is often
difficult to use only theoretical methods. Often theoretical, experimental data,
and dimensional analysis is used,

Some common pipe flow


components are shown:
Viscous Pipe Flow: Overview
Pipe flow versus Open-channel flow:
Open-Channel Flow:
Pipe Flow:

•Pipe is completely filled with fluid •Pipe is not full of fluids


•Pressure Gradients drive the flow •Pressure gradient is constant
•Gravity can also be important •Gravity is the driving force

i.e., flow down a concrete spill way.


Viscous Pipe Flow: Flow Regime
Osborne Reynolds Experiment to show the three regimes Laminar, Transitional,
or Turbulent:

Laminar

“Experiment”:

Transitional

Turbulent
Viscous Pipe Flow: Flow Regime
If we measure the velocity at any given point with respect to time in the pipe:

Re > 4000

Reynolds Number
Dependency: 2100< Re < 4000

Re < 2100

1. Turbulence is characterized by random fluctuations.


2. Transitional flows are relatively steady accompanied by occasional burst.
3. Laminar flow is relatively steady.

For laminar flow there is only flow direction:


For turbulent flow, there is a predominate flow direction, but there are
random components normal to the flow direction:
Viscous Pipe Flow: Entrance and Fully Developed
The entrance region in a pipe flow is quite complex (1) to (2):
The fluid enters the pipe with nearly uniform flow.
The viscous effects create a boundary layer that merges.
When they merge the flow is fully developed.

There are estimates for determining the entrance length for pipe flows:

and
Viscous Pipe Flow: Entrance and Fully Developed
For very low Reynolds numbers (Re = 10), the entrance length is short:
For large Reynolds number flow the entrance length can be several pipe
diameters:

For many practical engineering problems:


Bends and T’s affect Fully Developed Flow:
Pipe is fully developed until the character of the pipe changes.
It changes in the bend and becomes fully developed again after some length
after the bend.
Many disruptions can cause the flow to never be
fully developed.

In many flows, the fully developed region is greater than the developing region.
Viscous Pipe Flow: Pressure and Shear Stress

The shear stress in laminar flow is a direct result of momentum transfer along the
randomly moving molecules (microscopic).
The shear stress in turbulent flow is due to momentum transfer among the
randomly moving, finite-sized bundles of fluid particles (macroscopic).
The physical properties of shear stress are quite different between the two.
Fully Developed Laminar Flow: Overview
Both turbulent and laminar flows become fully developed in long enough straight
pipes. However, the details of the two flows are quite different.

Some important quantities that we calculate: velocity profiles, pressure drop, head
loss, and flow rate.

Although most flows are turbulent rather than laminar, and many pipes are not
long enough to allow the attainment of fully developed flow, a fully understanding
of fully developed laminar flow is important.

This study is the basis for more complex analysis, and there are some cases
where these assumption are good.

The equations or a description can be obtained in three different ways (1)


Momentum applied to a fluid element, (2) Navier-Stokes equations, and (3)
dimensional analysis methods.
Fully Developed Laminar Flow: Fluid Element Method
Basic Pipe flow is governed by a balance of viscous and pressure forces.

Consider and cylindrical fluid element within a pipe:

Free-Body Diagram:
Fully Developed Laminar Flow: Fluid Element Method
Now since neither the pressure gradient nor the length depend on r, the
R.H.S. must also be independent of r.
Then, Then at r = 0, t =0, and at r = D/2, t is the wall shear stress.

Now,

The shear profile is linear.

A small shear stress can produce a large pressure difference if the pipe is
relatively long.
The shear stress for laminar Newtonian Flow:

Velocity decreases from the center-line.


Fully Developed Laminar Flow: Fluid Element Method
Now, recall

Substitute, the shear stress definition, and rearrange:

Integrate,

Apply the boundary conditions, no-slip, u =0 at r = D/2, and solve for C1:

Vc = centerline velocity

Also, we can write in terms of shear stress:


Fully Developed Laminar Flow: Fluid Element Method
Find the Volumetric Flow Rate:

The average velocity is V.

The average velocity is 1/2Vc

or, Hagen-Poiseuille Flow


Fully Developed Laminar Flow: Fluid Element Method
Some general remarks:
1. The flowrate is directly proportional to the pressure drop.
2. The flowrate is inversely proportional to the viscosity.
3. The flowrate is inversely proportional to the pipe length.
4. The flowrate is inversely proportional to the pipe diameter to the 4th power.
We could adjust the equations for non-horizontal pipes:

Mean Velocity:

Volumetric Flow:

Lastly, we could develop these flows from Navier-Stokes as in Lecture 8.


Fully Developed Laminar Flow: Dimensional Analysis
Important Variables:
Density is not important because of “fully developed”

Number of dimensionless groups:

Two dimensional groups:

If we state that the pressure drop has to be directly proportional to l:

Or, solving for V, and substituting in Q:


C in this case must be determined by experimental analysis. It is 32 for
circular pipes.
Now, return to
and divide by dynamic pressure
Fully Developed Laminar Flow: Dimensional Analysis
Now, simplifying,

Now, rewriting, f is the Darcy Friction Factor (dimensionless).


Fully Developed Turbulent Flow: Overview
Turbulent flow is the least understood of all flow phenomena, yet is more
likely to occur than laminar flow, so we address ways of describing the flow.

Transition from Laminar to Turbulent Flow in a Pipe:


Fully Developed Turbulent Flow: Overview
One see fluctuation or randomness on the macroscopic scale.

mean fluctuating

One of the few ways we can describe turbulent flow is by describing it in


terms of time-averaged means and fluctuating parts.
Fully Developed Turbulent Flow: Overview
Now consider, the time average of the fluctuating parts:

The fluctuations are equally distributed on either side of the average.

Now, consider the average of the square of the fluctuations:

Turbulence Intensity:

Indication of the “gustiness” of the flow.


in Atmosphere, In “good” wind tunnel
Fully Developed Turbulent Flow: Overview
Now, shear stress:
However, for turbulent flow.
Laminar Flow: Turbulent Flow:

“Experiment”:

Shear relates to random motion Shear comes from eddy motion


as particles glide smoothly past which have a more random motion
each other. and transfer momentum.

For turbulent flow:


Is the combination of laminar and turbulent shear. If there are no fluctuations,
the result goes back to the laminar case. The turbulent shear stresses are
positive, thus turbulent flows have more shear stress.
Fully Developed Turbulent Flow: Overview
The turbulent shear components are known as Reynolds Stresses.
Shear Stress in Turbulent Flows: Turbulent Velocity Profile:

In viscous sublayer: tlaminar > tturb 100 to 1000 times greater.


In the outer layer: ttirb > tlaminar 100 to 1000 time greater.
The viscous sublayer is extremely small.
Fully Developed Turbulent Flow: Velocity Profile
The velocity profile for turbulent flow is been obtained through experimental
analysis, dimensional analysis, and semiempirical theoretical efforts.

In the viscous sublayer: for a smooth wall, “Law of the Wall”

is the friction velocity, and

In the overlap region:

From dimensional
analysis arguments
Possible outer region approximation:
Fully Developed Turbulent Flow: Velocity Profile
Some alternative, approach include the Power-Law equation:

n = 7 for many practical flows.

n, chosen based on the Reynolds number.

Turbulent velocity profiles are relatively flat in a pipe flow.


“Profiles”:
The power-law equation is not valid near the wall, since that would
give an infinite velocity gradient.
Also, the shear does not go to zero at the center-line.
Dimensional Analysis of Pipe Flow: Moody Chart
Most turbulent pipe flow data is based on experiments. In turbulent flow, in order
to do dimensional analysis we consider the roughness of the pipe, as well as
density which relates to momentum.

Variables:

roughness
Roughness is important in the viscous sub-layer
in turbulent flows, if it protrudes sufficiently in this
layer.
The viscous layer in laminar flow is so large, that
small roughness does not play a role.
Then range of roughness for validity of this
analysis is for:
Then, the dimensionless groups are the following:
Dimensional Analysis of Pipe Flow: Moody Chart
As for laminar flow, the pressure drop must be proportional to the pipe length:

Recalling the definition of the friction factor:

Then the friction factor is one of our dimensionless groups:


Then using experiments, we can find the above relationship with various
manufactured pipe roughness values:

“Moody Chart”

Colebrook Relation for Non-Laminar part of


the Moody Chart (curve fit):
Dimensional Analysis of Pipe Flow: Moody Chart

Laminar

Marks Reynolds Number


independence
Dimensional Analysis of Pipe Flow: Moody Chart
Energy Equation relation to Pipe Flow:

a’s account for non-uniform velocity profiles.


For fully developed pipe flow in a horizontal pipe:

And, Darcy-Weisbach Equation:


Some Example Problems

You might also like