Professional Documents
Culture Documents
There are two aspects of networking which must be considered when installing either an NCL or LMS product:
This presentation will focus on the RF side of the NCL and LMS products.
RF Terminology
Wavelength is the distance between identical points in the adjacent cycles of a waveform. In wireless systems, this length is usually specified in meters, centimeters, or millimeters
The size of the wavelength varies depending on the frequency of the signal. Generally speaking, the higher the frequency the smaller the wavelength.
The WaveRider family of products operate in the 2.4000 2.4835 GHz range (NCL and LMS2000) as well as the 905 925 MHz range (LMS3000). At 2.4 GHz the wavelength is 12.5cm At 905 MHz the wavelength is 33cm
These values are calculated using the following formula: Wavelength = 3 x 102 f (frequency in MHz)
This calculation is important to remember, especially when installing antennas. Ideally, the antenna should be installed no closer than 10 wavelengths to the nearest reflective surface.
Frequency
Frequency is the number of complete cycles per second in alternating current direction. The standard unit of frequency is the hertz, abbreviated Hz. If a current completes one cycle per second, then the frequency is 1 Hz.
Frequency Spectrum
Designation Very Low Frequency Low Frequency Medium Frequency High Frequency Very High Frequency Ultra High Frequency Super High Frequency Extremely High Frequency
Frequencies 9 kHz - 30 kHz 30 kHz - 300 kHz 300 kHz - 3 MHz 3 MHz - 30 MHz 30 MHz - 300 MHz 300 MHz - 3 GHz 3 GHz - 30 GHz 30 GHz - 300 GHz
Spectrum
800 DAMPS GSM/NMT EGSM TACS ETACS PDC AMPS iDEN 806 821 ESMR 806 824 UP-SMR NPCS PAGING ISM 824 849 851 866 851 869
896901 901902 930931 940 945 940 941
900 915 915 890 905 872 905 917 925 935 950 950 935
2000
2500
2400-2483.5
Tx Power
Tx is short for Transmit
All radios have a certain level or Tx power that the radio generates at the RF interface. This power is calculated as the amount of energy given across a defined bandwidth and is usually measured in one of two units: 1. dBm a relative power level referencing 1 milliwatt
2. W a linear power level referencing Watts
The NCL and LMS radios have Tx power of +18dBm, which translates into .064 W or 64 mW.
Rx Sensitivity
Rx is short for Receive All radios also have a certain point of no return, where if they receive a signal less than the stated Rx Sensitivity, the radio will not be able to see the data. This is also stated in dBm or W. The NCL and LMS radios have a receive sensitivity of 82 dBm. At this level, a Bit Error Rate (BER) of 10-5 (99.999%) is seen. The actual level received at the radio will vary depending on many factors.
Radiated Power
In a wireless system, antennas are used to convert electrical waves into electromagnetic waves. The amount of energy the antenna can boost the sent and received signal by is referred to as the antennas Gain. Antenna gain is measured in:
1. dBi: relative to an isotropic radiator 2. dBd: relative to a dipole radiator 0 dBd = 2.15 dBi
There are certain guidelines set by the FCC that must be met in terms of the amount of energy radiated out of an antenna. This energy is measured in one of two ways: 1. Effective Isotropic Radiated Power (EIRP) measured in dBm = power at antenna input [dBm] + relative antenna gain [dBi] 2. Effective Radiated Power (ERP) measured in dBm = power at antenna input [dBm] + relative antenna gain [dBd]
Energy Losses
In all wireless communication systems there are several factors that contribute to the loss of signal strength. Cabling, connectors, lightning arrestors can all impact the performance of your system if not installed properly. In a low power system (such as the NCL and LMS products) every dB you can save is important!! Remember the 3 dB Rule. For every 3 dB gain/loss you will either double your power (gain) or lose half your power (loss).
-3 dB = 1/2 power -6 dB = 1/4 power +3 dB = 2x power +6 dB = 4x power Sources of loss in a wireless system: free space, cables, connectors, jumpers, obstructions
FCC Guidelines
The ISM Bands are defined as follows: 902 to 928 MHz 2400 to 2483.5 MHz 5725 to 5850 MHz
FCC Part 15, Class B Unlicensed operation from 2400 to 2483.5 MHz P2P - EIRP : +36 dBm (4 Watts) : 3:1 i.e. +24 dBm into 24 dBi P2MP - EIRP : +36 dBm (4 Watts) : 3:1 at subscriber (considered P2P)
FCC - Installer
System must be installed by a Professional Installer as defined in FCC Document 15.247 Part 15;
Complete understanding of FCC emissions regulations for unlicensed operation in the 2.4 GHz ISM Band.
Installer must have a full understanding of the impact of various types of antennae, amplifiers and other active and passive components on the compliance of the equipment under FCC regulations.
FCC - Installation
An external Power Amp cannot be used in conjunction with WR radio components, in order to comply with FCC regulatory emissions requirements. Use of an external PA device with a WaveRider system is deemed illegal and may result in significant penalty to the manufacturer, seller, and customer.
When transmitted, the data is combined with a higher data-rate bit sequence (also known as a chipping code) that divides the data according to a spreading ratio.
The transmitter and the receiver must be synchronized with the same spreading code. The chipping code helps the signal resist interference and also enables the original data to be recovered if data bits are damaged during transmission.
22 MHz wide
FHSS an example
f5 f4 f3 f2 f1 1 2 3 4 5 6 7 TIME 8 9 10 11 12
Signal Propagation
As the signal leaves the antenna it propagates, or disperses, into space. The antenna selection will determine how much propagation will occur. At 2.4 GHz it is extremely important to ensure a that a path (or tunnel) between the two antennas is clear of any obstructions. Should the propagating signal encounter any obstructions in the path, signal degradation will occur. Trees, buildings, hydro poles, and towers are common examples of path obstructions.
The greatest amount of loss in your wireless system will be from Free Space Propagation. The Free Space Loss is predictable and given by the formula: FSL(dB) = 32.45 + 20Log10F(MHz) + 20Log10D(km) The Free Space Loss at 1km using a 2.4 GHz system is:
Line of Sight
Attaining good Line of Sight (LOS) between the sending and receiving antenna is essential in both Point to Point and Point to Multipoint installations.
Generally there are two types of LOS that are used discussed during installations:
1. Optical LOS - is related to the ability to see one site from the other 2. Radio LOS related to the ability of the receiver to see the transmitted signal
To quantify Radio Line of Sight, the Fresnel Zone theory is applied. Think of the Fresnel Zone as a football shaped tunnel between the two sites which provides a path for the RF signals.
At WaveRider acceptable Radio Line of Sight means that at least 60% of the first Fresnel Zone plus 3 meters is clear of any obstructions.
Fresnel Zones
3rd*
2nd*
1st*
* Fresnel Zones
Site A
rn =
nl d d d +d
1
1 2 2
d1
Fresnel Zone diameter depends upon
Wavelength, and Distances from the sites along axis For minimum Diffraction Loss, clearance of at least 0.6F1+ 3m is required
Site B
d2
When obstructions intrude on the first Fresnel Zone many issues can arise which will affect the performance of the system. The main issues are: 1. Reflection incident wave propagates away from smooth scattering plane multipath fading is when secondary waves arrive out-ofphase with the incident wave causing signal degradation
2. Refraction incident wave propagates through scattering plane but at an angle frequencies less than 10 GHz are not affected by heavy rains, snow, pea-soup fog at 2.4 GHz, attenuation is 0.01 dB/Km for 150mm/hr of rain
Path Profile characteristics may change over time, due to vegetation, building construction, etc.
FiveNines V1.2
The type of system you are installing will help determine the type of antenna used. Generally speaking, there are two types of antennae: 1. Directional - this type of antenna has a narrow beamwidth; with the power being more directional, greater distances are usually achieved but area coverage is sacrificed - Yagi, Panel, Sector and Parabolic antennae
- an EUM, NCL Station/Master will use this type of antenna in both Point to Point and Point to Multipoint
2. Omni-Directional
- this type of antenna has a wide beamwidth and radiates 3600; with the power being more spread out, shorter distances are achieved but greater coverage attained - Omni antenna - a CCU or an NCL Master will use this type of antenna
Yagi
- better suited for shorter links - lower dBi gain; usually between 7 and 15 dBi
Parabolic
- used in medium to long links
- gains of 18 to 28 dBi - most common
Sectoral
- directional in nature, but can be adjusted anywhere from 450 to 1800 - typical gains vary from 10 to 19 dBi
180
180
Omni
- used at the CCU or Master NCL for wide coverage - typical gains of 3 to 10 dBi
Polarization
An antennas polarization is relative to the E-field of antenna. If the E-field is horizontal, than the antenna is Horizontally Polarized. If the E-field is vertical, than the antenna is Vertically Polarized.
No matter what polarity you choose, all antennas in the same RF network must be polarized identically regardless of the antenna type.
Polarization may deliberately be used to: Increase isolation from unwanted signal sources (Cross Polarization Discrimination (x-pol) typically 25 dB) Reduce interference Help define a specific coverage area
Horizontal
Vertical
Antenna Impedance
A proper Impedance Match is essential for maximum power transfer. The antenna must also function as a matching load for the Transmitter ( 50 ohms). Voltage Standing Wave Ratio (VSWR), is an indicator of how well an antenna matches the transmission line that feeds it. It is the ratio of the forward voltage to the reflected voltage. The better the match, the Lower the VSWR. A value of 1.5:1 over the frequency band of interest is a practical maximum limit.
Return Loss is related to VSWR, and is a measure of the signal power reflected by the antenna relative to the forward power delivered to the antenna. The higher the value (usually expressed in dB), the better. A figure of 13.9dB is equivalent to a VSWR of 1.5:1. A Return Loss of 20dB is considered quite good, and is equivalent to a VSWR of 1.2:1.
D istance-to-fault
CH E R-B-A 04
M1 : -3 .7 2 8 d B @ 5 0 .6 9 8 Fe e t -1 0
R e tu r n L o s s ( d B )
-2 0
-3 0
-4 0
-5 0 0 5 10 15 25 30 35 40 D i s ta n c e (0 .0 - 6 0 .0 Fe e t) CA L : O N (CO A X ) O u tp u t P o w e r : - 3 0 .0 0 d B m T im e : 1 2 :0 3 :5 9 S e r ia l # : 0 0 0 0 4 0 9 6 20 45 50
M1
55
60
CW O n
R e so lu tio n : 2 5 9 B ia sT e e : O F F D a te : 0 6 /2 7 /2 0 0 0 M o d e l: S 3 3 2 B
Environmental Effects
Ice and wind loading, Salt spray Radomes used to improve performance in icy, windy conditions (more common with larger solid parabolic dishes). Wind loading can be reduced substantially by using a radome. Wind loading can produce vibration, which in turn can produce azimuth errors. For longer paths, this can be critical. Installation - pay close attention to proper sealing of all connector junctions.
Attenuation Table
Cable Type Attenuation at 2.4 GHz per 100 feet RG8 10 LMR400 6.8 Heliax 3/8" 5.36 LMR600 5.4 Heliax 1/2" 3.74 Heliax 5/8" 2.15
Line Loss or Attenuation paramount refer to your Link Budget Calculations to determine how much loss is acceptable and still have a viable link. Foam dielectric, Air Dielectric, Pressurized types of Coaxial Cable. Waveguide use also possible but typically not costeffective
Connectors
Your connector selection will be determined based on the following: - connector gender at antenna
For the most part the cabling manufacturers also manufacture the connectors that go on the cables. Knock off connectors are available, but dont always fit the cable the way the manufacturers connectors do. Generally the only decision that needs to be made is what gender of connector to installMale or Female
Antennas usually Female Lightning Arrestors usually Female
Connectors
N-male
RP-SMA- male
N-female
RP-SMA-female
For maximum protection, ground must be connected close to point of entry into building - within 2ft.
Typically structural steel OK for ground connection Do not use Gas Lines or Water pipes.
Typical Lightning Arrestor
- Backhaul Design
Fade Margin Defined as the difference between the Receive Signal Level RSL, and the Rx Threshold or other chosen reference Level. For path lengths of 16km or less, a minimum 10dB Fade Margin is recommended
Ie. If you have an RSL of 60dB and a Rx Threshold of 72dB, than your fade Margin would be 12dB
Antenna Gain (dBi) A Path Loss (dB) Field Factor (dB) Connector
Losses
(dB) Cable Losses (dB) Cable Losses (dB)
Loss(dB) - Field Factor (dB) + Total Antenna Gains (dB) - Total Cable Losses (dB) - Total Connector Losses (dB)
Customer Elevation (ft) Latitude Longitude Azimuth Antenna Type HAAT (ft) Antenna Gain (dBi) Tx Line Type Tx Line Length (ft) Tx Line Loss (dB/100 ft) Tx Line Loss (dB) Connector Loss (dB) Amplifier Type Amplifier Tx Gain (dB) Frequency (MHz) Path Length (mi) Free Space Loss (dB) Diffraction Loss (dB) Net Path Loss (dB) Radio Type Model Tx Power (mW) Tx Power (dBm) Effective Isotropic Radiated Power (dBm) Effective Isotropic Radiated Power (W) Amplifier Rx Effective Gain (dB) Rx Sensitivity for max. Throughput (dBm) Rx Signal Level (dBm) Fade Margin (dB)
CAP1
Subscriber1
70.00 60.00 4.42 4.42 3.09 2.65 1.50 1.50 HA-2401E-100/10 HA-2401E-100/10 0.00 0.00 2450.00 4.00 116.36 0.00 116.36 116.36 CCU2000 EUM2000 31.62 31.62 15.00 15.00 24.91 34.85 0.31 3.05 10.00 10.00 -72.00 -72.00 -61.60 -61.60 10.40 10.40
Product:
NCL1135-A
LPA
Site1
EIRP= 35.5 dBm Distance= EIRP = 35.5 dBm 8 Km Antenna Gain Para 24 dBi 2 Pwr @ Ant Cable Type LMR-600 Path Loss = 118.2 dB Cable Length Feed Loss Frequency = 2450 MHz Amp Gain No Amplifier 3 10 When using amp check notes. Output Power 15 dBm Rx Power -62 dBm Fade Margin 10 dB 14 m 1 3.5 dB 11.5 dBm
Site2
Antenna Gain Para 24 dBi 2 Pwr @ Ant Cable Type Cable Length Feed Loss Amp Gain 11.5 dBm
LMR-600
14 m 63 3.5 dB
No Amplifier
16 10 When using amp check notes. Output Power 15 dBm Rx Power -62 dBm Fade Margin 10 dB
14
14
Notes
FRESNEL ZONE CLEARANCE - USE Calc - General for Obstruction Unit Converter
Enter distance in miles 18 75 20 21 = = = = 29.0 km 22.86 m 12.4 miles 68.90 feet
This tool is intended as a guideline only. It is the user's responsibilty to ensure the link design meets the local regulatory agency guidelines.
Interference Countermeasures
1. Short Paths 2. Narrow Beam Antennas (high gain) 3. Frequency Selection 4. Antenna Polarization 5. Antenna Azimuth 6. Equipment/Antenna Location